000 |
D |
** Customizing ** |
001 |
D |
Das Merkmal &1 hat falsche Eigenschaften |
002 |
D |
Das Merkmal &1 gehört nicht zur Klasse &2 |
003 |
D |
Kein Filter/Fokus entsprechend der Selektionkriterien gefunden |
004 |
D |
Wählen Sie einen Filter/Fokus |
005 |
D |
Selektionskriterien wurden geändert, Auswahl aus alten Ergebnissen |
006 |
D |
Parameter für den Funktionsbaustein &1 sind unvollständig |
010 |
D |
** Allgemeine Prüfungen ** |
011 |
D |
Cancel-Part-Prüfung ist wg. fehl. Customizing-Einstellung nicht möglich |
012 |
D |
&1 &2 / Teil &3: Dokument &4 fehlt im Arbeitsumfang |
013 |
D |
&1 &2: Teil &3 gemäß der Variantenkonfiguration oder ECM nicht gültig |
014 |
D |
&1 &2: Teil &3 ist gemäß des Arbeitsumfanges nicht gültig |
015 |
D |
&1 &2 ist der Klasse &3 Klassenart &4 nicht zugeordnet |
016 |
D |
&1: Fehlender Wert für Kennzeichen &2 in Klasse &3 Klassenart &4 |
017 |
D |
&1 &2: CANCEL-Part-Merkmal fehlt in Klasse &3 Klassenart &4 |
018 |
D |
&1 &2: Teil &3 is kein CANCEL-Teil für &4 |
019 |
D |
&1 &2 enthalten keine Teilenummer |
020 |
D |
Teil &1 ist ein voll austauschbares Material |
021 |
D |
Prüfungen wurden aufgrund fehlendem Customizing nicht durchgeführt |
022 |
D |
Das aktuelle Teil &1 ist an diesem Einbauort nicht möglich |
023 |
D |
&1 &2: Das aktuelle Teil &3 ist nicht als Cancel-Teil für &4 vorgesehen |
024 |
D |
&1 &2: Sowohl das akt. Teil als auch das Cancel-Teil sind nicht angegeben |
025 |
D |
&1 &2 &3 &4 |
026 |
D |
Verschiedene Konfigurationen für Funktionskennzeichen &1 gefunden |
050 |
D |
** Prüfungen auf Set-Beziehungen ** |
051 |
D |
Teil &1 steht in Beziehung zu &2 &3 mit unbekannter Abhängigkeit |
052 |
D |
Set &1 &2: Keine Infos über eingebaute Teile für &3 &4 vorhanden |
053 |
D |
Nicht zulässige Kombination von Teil &1 in &2 und Teil &3 in &4 |
070 |
D |
** Nachrichten für iPPE-Testanwendung ** |
071 |
D |
BAdI-Implementierung MPL_TEST ist nicht aktiv |
072 |
D |
Nachrichten: Testanwendung für die Schnittstelle zur iPPE-Workbench |
080 |
D |
Die Klasse & wurde erfolgreich angelegt |
081 |
D |
Das Merkmal & wurde erfolgreich angelegt |
899 |
D |
Customizing for released characteristic status (table TCMS) missing |
000 |
E |
** Customizing ** |
001 |
E |
The characteristic &1 has wrong properties |
002 |
E |
Characteristic &1 does not belong to the class &2 |
003 |
E |
No filter/focus matching the selection was found |
004 |
E |
Choose a filter/focus |
005 |
E |
Selection criteria were changed. Selection is from the old results. |
006 |
E |
Parameters for function module &1 are incomplete |
010 |
E |
** General Checks ** |
011 |
E |
Cancel-part check not possible because of missing Customizing settings |
012 |
E |
&1 &2 / part &3: Document &4 is missing in work scope |
013 |
E |
&1 &2: Part &3 not valid according to variant configuration or ECM |
014 |
E |
&1 &2: Part &3 is not valid according to work scope |
015 |
E |
&1 &2 is not assigned to class &3 class type &4 |
016 |
E |
&1: Missing value for characteristic &2 in class &3 class type &4 |
017 |
E |
&1 &2: CANCEL-Part characteristic missing in class &3 class type &4 |
018 |
E |
&1 &2: Part &3 is not a CANCEL part for &4 |
019 |
E |
&1 &2 does not contain a part number |
020 |
E |
Part &1 is a fully interchangeable part |
021 |
E |
No checks are run because of missing Customizing settings |
022 |
E |
The current part &1 is not possible at this location |
023 |
E |
&1 &2: The current part &3 is not intended as a cancel part for &4 |
024 |
E |
&1 &2: Neither the current part nor the cancel part are not specified |
025 |
E |
&1 &2 &3 &4 |
026 |
E |
Various configurations found for function identifier &1 |
050 |
E |
** Checks on Set relations ** |
051 |
E |
Part &1 is related to &2 &3 with unknown dependencies |
052 |
E |
Set &1 &2: No information is available for installed parts for &3 &4 |
053 |
E |
Combination of part &1 in &2 and &3 in &4 is not allowed |
070 |
E |
** Messages for the iPPE test application ** |
071 |
E |
BADI implementation 'MPL_TEST' is not active |
072 |
E |
Messages: Test application for the interface to the iPPE workbench |
080 |
E |
Class & successfully created |
081 |
E |
Characteristic & successfully created |
899 |
E |
Customizing for released characteristic status (table TCMS) missing |